Rhino(犀牛)中国技术支持与推广中心

标题: 模具名词翻译 [打印本页]

作者: Jessesn 时间: 2010-7-18 19:27
标题: 模具名词翻译
top view    ----俯视图
front view    ----前视图
side view    ----侧视图
plane view ----平面图
contour ------外型铣削
pocket ------挖槽
flow line    ----罩一曲面
multisurf ------多重曲面
filter    -----过滤
ellipse    -----椭圆
polar -------极坐标
arc endpoints-----两点画弧
polygon -------多边形
isometric -------等角视图
zig zag -------双向
one way -------单向
spline -------圆滑曲线
blend -------顺接
guide pin --------导针;边针;直边
support pin ---------拉杆;水口边
support pin collar    --------拉杆定位;水口边定位介子
tapped hold for eyebolt -------吊模螺孔
thermal expansion coefficient -------热膨胀系数
welding rod    -------熔接棒
cavity plate; A bolster plate -----母模板 (A板), 前模板
stripper plate    ---------活动板,推料板
core plate    --------公模板 (B板),后模板
spacer block -----------间隔板
ejector retainer plate -----------上顶针板
ejector plate -----------下顶针板
pin point gate system ---------小水口系统
side gate system -----------大水口系统
infrared-transmitter --------红外线发射器
infrared-receiver ------------红外线接受器
synthetic resin ------------合成权脂
air blow gun(with nozzles&hose) -------------气枪
spiral hose    -------------螺旋形的;盘旋的
guide strip    ---------------行位导轨
ejector rod    --------------斜坊
set screw    ---------固定螺丝
countersunk screw    ---------沉头螺丝
hex screws    --------胚头螺丝
shoulder screw -----------------带肩螺丝
residual stress -----------------残余应力
tensile ---------------------------------张力
electricity erode -----------------电蚀刻
ohm meter    -------------------电阻表
tubular dowel -----------------管钉,销钉
abrasive stone -----------------研磨石材
SPI Mold Finish Comparison Kit --SPI模具抛光比照工具
rolled    ------------------热轧
forged    ------------------热锻
extrude    ------------------挤压
cold drawn    -------------------冷拉
corrosive plastics -----------------防腐塑料
tough    -----------------硬度
anneal    -----------------n.退火
service life    --------------------注塑寿命
high viscosity -----------------粘度较高的
extension plug ------------------延伸尾塞
angle plug    -------------------斜角尾塞
thermocouple connector ---热电偶连结头
hydraulic system ---(注塑机的)油压系统
temperature control zone  -------------------温控区
barrel heating capacity ----料筒加热能力
screw torque    ----------------螺杆力矩
screw speed    -------------------螺杆速度
screw stroke    ----------------螺杆行程
nozzle contact force    --------热嘴接触力
screw L/D ratio    ------螺杆长度/直径比例
theoretical shot volume ---理论的注射容量
clamp force    --------------------合模力
lock force    ---------------------------锁模力
internal heated ------------------------内部加热
external heated ------------------------外部加热
heating rod    -------------------------加热棒
air-gap insulation ------------------------空气隔绝层
spare part(accesory)    -------------备用件
insulating ring -----------------------绝缘圈
sealing washer -------------------垃圾钉
adaptor ---------------------适配器
hole gauge ----------------------孔深量测仪
high-temperature grease ------高温油脂
thermal conductivity paste --------导热膏
data cable    --------------数据线
compression mold base    -------压缩模胚
countersunk    -----------------埋头孔锥孔,沉孔
mill    --------------压榨机;磨坊;碾磨;
drill    ---------------钻头;钻床钻孔;钻通
grind    -----------------磨擦;磨碎;磨光
turn    ---------------转动;旋转;翻转
adapter plate -----------------适配模板
leader pin; shoulder leader pin ----导针;带肩导针( 实心)
angle pin(horn pin) ---------斜针;斜边
straight bushing    ----------直导套(空心)
shoulder bushing    ----------带肩导套
sprue puller pin    ----------唧咀扣针
sprue spreader    -----------浇口分流锥
runner spreader    -----------流道分流锥
tapered interlocks(round & rectangular) ---------啤把锁
bronze plated bushing    ------镀铜导套
guided ejection bushing ------导向导套
toggle-lock early ejector return ----切换式早期回撞装置
accelerated knock-out    ----------加速顶棍
accelerated ejector    ------------加速顶针
collapsible core    ---------可折迭式的型芯
slide retainer    ------------行位固定装置
jiffy latch-lock assemblies -------------快速拉杆锁定装置
tapped hole    ------------------螺丝孔
no resettable shot counter    -----------非复位注射计数器
profiled ejector pin    ------------底面在有倾斜截面的顶针
copper    -------红铜
brass    ------- 黄铜
bronze    --------青铜
BeCu    --------铍铜
counterbore    ---------------拔头,介子托
fan gate    -----------------扇形入口
fillet    ----------------圆形入口
pin point gate    -------------细水口
hose clip    --------------入喉箍
jiggle    ----------------斜顶
British Standard Whitworth thread BSW --英制螺丝(粗牙)
British Standard Fine Thread BSF    -------英制螺丝(幼牙)
British Standard Pipe Thread (BSP) --------英制喉牙
National Pipe Thread    -----------------------美制螺牙
pressure plug    ----------------喉塞
pressure spring    -----------------压力弹簧
vent    ------------------ 疏气孔
alignment strip    --------------------斜锁
ball catch    ---------------------弹弓波子
bridge piece    ------------------水口铁
Jiffy-matic connector ---------------------快速连接喉
All ejector blades must have key to avoid rotating. 扁顶针要止转
ejector bearing length 弹弓压缩长度
reinforcement rib 加强筋
steel pad 方铁
latch 拉杆
sprue puller insert 扣针导套
stage ejector=knock out 顶棍
ejector retainer plate    上顶针板
ejector base plate 下顶针板
stripper plate 活动板
runner stripper plate 脱料板
P/L flash 分形面披锋
scrape 拖花
burn 烧黑
safety strap 码板
side gate system 大水口系统
three plate type system 简化型细水口系统
pin point gate system 细水口系统
guide pin/guide bush 直边/托司
top clamp plate 工字板
stripper plate    推板
spacer block 方铁
bottom clamp plate    底板
shoulder guide pin 带肩导针
shoulder guide bush 托司
straight guide bush 直司/直导套
guide pin 直边
screw thread 螺纹
air pump 空气泵
alloy    合金
alloy steel 合金钢
fixed clamp plate;top clamping plate;top plate定模座块
动模座块 moving clamp plate;bottom clamping plate
上模座块 upper clamping plate
下模座块 lower clamping plate
凹模固定板 cavity-retainer plate
型芯固定板 core-retainer plate
突模固定板 punch-retainer plate
模套 chase;bolster;frame
支承板 backing plate;support plate
垫块 spacer;parallel
支架 ejector housing,mould base leg
斜销 angle pin,finger cam
滑块 slide,cam slide
侧芯型滑块 side core slide
滑块导板 side guide strip
楔紧块,撑鸡 heel block,wedge bock
斜槽导板 finger guide plate
弯销 dog-leg cam
斜滑块 angle-lift splits
导向零件
导柱 guide pillar;guide pin;leader pin
推板导柱 ejector guide pillar;ejector guide pin
带头导套 guide bush;guide bushing
推板导套 ejector guide bush;ejector bushing

定位和限位零件
锥形定位件 mould bases locting elements
复位杆 ejector plate return pin,push-back pin
限位块 stop block; stop pad
定距拉杆 length bolt; puller bolt
定距拉板 puller plate; limit plate

推出零件
推流道板 runner stripper plate
分流道拉料杆 runner puller; runner lock pin
拉流杆;扣针 sprue puller
钩形拉料杆 sprue puller, Z-shaped
球头拉料杆 sprue puller,ball-headed
圆锥头拉料杆 sprue puller,conical headed
连接推杆 ejector tie rod
推板 ejector plate;ejection plate
推杆固定板 ejector retainer plate
推件环(盘) stripper ring(disk)
推件板 stripper plate
推块 ejector pad
推管(司筒,导筒) ejector sleeve
推杆 ejector pin
圆柱头推杆 ejector pin with cylindrical head
带肩推杆 shouldered ejector pin
扁推杆 flat ejector pin

作者: jdl198561 时间: 2010-7-18 19:42
呵呵好精彩
有详细的运用案例不期待

作者: fm0216 时间: 2010-7-18 20:30
好东西可惜不太懂

作者: 咖啡和糖 时间: 2010-7-18 20:33
好资料，收藏了~

作者: fengyun319 时间: 2010-7-19 07:31
很专业啊！

作者: huxuewu 时间: 2010-7-23 18:50
顶！

作者: s.k. 时间: 2011-9-4 21:52
强大啊

作者: ll. 时间: 2012-3-2 10:38
ding feichangjingcai

作者: LYSBSB 时间: 2014-6-30 16:07
好东西啊

欢迎光临 Rhino(犀牛)中国技术支持与推广中心 (http://bbs.rhino3d.asia/)